服務	櫥柜	詳細地址	路北-橡塑路
QQ號	1334576766

異型鋼單縫式伸縮裝置

GQFC型、GQFZ型、GQFL型、GQFF型、GQFMZL型模數式橋梁伸縮裝置，是采用熱軋整體成型的異型鋼材設計的橋梁伸縮裝置。GQFC型、GQFZ型、GQFF型、GQFL型伸縮裝置適用于伸縮量80mm以下的橋梁接縫，GQFMZL型伸縮裝置是由邊梁、中梁、橫梁和連動機構組成的模數式橋梁伸縮裝置，適用于伸縮量80mm-1200mm的大中跨度橋梁。

GQF C type， GQF Z type， GQF L type， GQF F type and GQF MZL modulus bridge expansion device are bridge expansion devices designed by hot rolled integral shaped steel products. GQF - C bridge joint type， GQF - Z， GQF - F， GQF - L telescopic device is suitable for the expansion amount below 80mm， GQF - MZL type expansion device is a modular bridge expansion device is composed of edge beam， beam， beam and linkage mechanism， suitable for large and medium expansion 80mm-1200mm long span bridge.

2、設計制造技術條件

2. Technical conditions for design and manufacture

1、設計荷載：采用J刊公路工程技術標準規定的汽車超過20級荷載進行設計。

1， design load using J magazine 01 - highway engineering technical standard stipulated in the vehicle over 20 load to carry out the design.

2、本結構使用的異型鋼材質為16Mn橋梁專用鋼，鋼材抗拉強度應不低于480Mpa，容許彎曲應力不低于210Mpa。

2. The special-shaped steel material used in this structure is 16Mn bridge special steel. The tensile strength of steel should not be less than 480Mpa， and the ading stress is not less than 210Mpa.

3、結構中支承橫梁使用16Mn或45號鋼，其容許彎曲應力不低于210Mpa。

3. 16Mn or No. 45 steel is used in the supporting beam in the structure， and the ading stress is not less than 210Mpa.

4、其余配件鋼材可使用不低于Q235強度鋼材。

4， the rest of the fittings steel can be used not less than Q235 strength steel.

3、膠料適用范圍

3. The scope of application of rubber

1、采用氯丁橡膠（C日）的伸縮裝置適用于溫度為25+60地區。

1. The telescopic device used for chloroprene rubber （C day） is suitable for the temperature range of - 25 - C - +60 C.

2、采用天然橡膠（N日）的伸縮裝置適用于溫度為40+60地區。

2. The expansion device of natural rubber （N day） is suitable for the temperature range of - 40 C to +60 C.

異型鋼單縫式伸縮裝置

A single slit expansion device for special-shaped steel

異型鋼單縫式伸縮裝置由一條整長的橡膠密封條，一組鋼質邊梁及錨固件組成。鋼質邊梁內側帶 有能固定橡膠密封條的溝漕。焊固在鋼梁外側的錨固件，與梁端預埋鋼筋相焊接，澆筑高強度混凝土過渡段后，同志梁體連接可靠，具有與橋面接合平順，密封止 水，伸縮靈活，行車平穩，使用壽命長的特點。適用于伸縮量0-80mm的橋梁。

The special-shaped steel single slit expansion device consists of a whole long rubber seal， a group of steel side beams and anchors. The inside of the steel side beam has a ditch that can be fixed with a rubber seal. The anchorage piece fixed on the outer side of the steel beam is welded with the embedded steel bar at the beam end. After pouring the transition section of the high strength concrete， the connection of the comrade beam body is reliable， and has the characteristics of smooth connection with the bridge deck， sealing and water stopping， flexible expansion， stable driving and long service life. The bridge is suitable for the expansion of 0-80mm.

異型鋼單縫式伸縮裝置伸縮量的確定

Determination of expansion capacity of single slit expansion device for special-shaped steel

橋梁伸縮量計算值直接影響對伸縮縫規格選定，若伸縮縫規格選擇不合理， 就直接影響伸伸縮縫的使用效果，同時選擇伸縮裝置時還應考慮梁、 板間伸縮裝 置間隙量大小，以保證伸縮縫裝置與梁、板兩端有充分錨固，才能達到佳使用效果。所以在選擇伸縮縫的規格時，一定要留充足余量，才能保證伸縮縫的使用 效果和耐久性.1

The value of a direct impact on the expansion joint specifications selection calculation of bridge expansion joints， if the specifications are not reasonable， directly affects the use effect of stretch contraction joints， and telescopic device should be taken into consideration when the beam and plate expansion device gap size， to ensure that the expansion joint device and beam， plate ends have sufficient anchorage， can to achieve the best results. So when choosing the size of the expansion joint， we must leave sufficient allowance to ensure the use effect and durability of the expansion joint.1.